diff options
Diffstat (limited to 'simonnnnn/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h')
-rw-r--r-- | simonnnnn/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h | 460 |
1 files changed, 460 insertions, 0 deletions
diff --git a/simonnnnn/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h b/simonnnnn/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h new file mode 100644 index 0000000..eb37fe0 --- /dev/null +++ b/simonnnnn/Drivers/STM32L0xx_HAL_Driver/Inc/stm32l0xx_hal_pwr.h @@ -0,0 +1,460 @@ +/**
+ ******************************************************************************
+ * @file stm32l0xx_hal_pwr.h
+ * @author MCD Application Team
+ * @brief Header file of PWR HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright(c) 2016 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L0xx_HAL_PWR_H
+#define __STM32L0xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l0xx_hal_def.h"
+
+/** @addtogroup STM32L0xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup PWR PWR
+ * @{
+ */
+
+/** @defgroup PWR_Exported_Types PWR Exported Types
+ * @{
+ */
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+ * @brief PWR PVD configuration structure definition
+ */
+typedef struct
+{
+ uint32_t PVDLevel; /*!< PVDLevel: Specifies the PVD detection level.
+ This parameter can be a value of @ref PWR_PVD_detection_level */
+
+ uint32_t Mode; /*!< Mode: Specifies the operating mode for the selected pins.
+ This parameter can be a value of @ref PWR_PVD_Mode */
+}PWR_PVDTypeDef;
+#endif
+
+/**
+ * @}
+ */
+
+/** @addtogroup PWR_Private
+ * @{
+ */
+
+#if defined(PWR_PVD_SUPPORT)
+#define PWR_EXTI_LINE_PVD EXTI_FTSR_TR16 /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+#endif
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+ * @{
+ */
+
+/** @defgroup PWR_register_alias_address PWR Register alias address
+ * @{
+ */
+#define PWR_WAKEUP_PIN1 PWR_CSR_EWUP1
+#if defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#else
+#define PWR_WAKEUP_PIN2 PWR_CSR_EWUP2
+#endif
+#if defined (STM32L010x4) || defined (STM32L010x6) || defined (STM32L011xx) || defined (STM32L021xx) || \
+ defined (STM32L031xx) || defined (STM32L041xx) || defined (STM32L071xx) || defined (STM32L072xx) || \
+ defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define PWR_WAKEUP_PIN3 PWR_CSR_EWUP3
+#endif
+/**
+ * @}
+ */
+
+#if defined(PWR_PVD_SUPPORT)
+/** @defgroup PWR_PVD_detection_level PVD detection level
+ * @{
+ */
+#define PWR_PVDLEVEL_0 PWR_CR_PLS_LEV0
+#define PWR_PVDLEVEL_1 PWR_CR_PLS_LEV1
+#define PWR_PVDLEVEL_2 PWR_CR_PLS_LEV2
+#define PWR_PVDLEVEL_3 PWR_CR_PLS_LEV3
+#define PWR_PVDLEVEL_4 PWR_CR_PLS_LEV4
+#define PWR_PVDLEVEL_5 PWR_CR_PLS_LEV5
+#define PWR_PVDLEVEL_6 PWR_CR_PLS_LEV6
+#define PWR_PVDLEVEL_7 PWR_CR_PLS_LEV7 /* External input analog voltage
+ (Compare internally to VREFINT) */
+/**
+ * @}
+ */
+
+/** @defgroup PWR_PVD_Mode PWR PVD Mode
+ * @{
+ */
+#define PWR_PVD_MODE_NORMAL (0x00000000U) /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING (0x00010001U) /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING (0x00010002U) /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING (0x00010003U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING (0x00020001U) /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING (0x00020002U) /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING (0x00020003U) /*!< Event Mode with Rising/Falling edge trigger detection */
+/**
+ * @}
+ */
+#endif /* PWR_PVD_SUPPORT */
+
+/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
+ * @{
+ */
+#define PWR_MAINREGULATOR_ON (0x00000000U)
+#define PWR_LOWPOWERREGULATOR_ON PWR_CR_LPSDSR
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+ * @{
+ */
+#define PWR_SLEEPENTRY_WFI (0x01U)
+#define PWR_SLEEPENTRY_WFE (0x02U)
+/**
+ * @}
+ */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+ * @{
+ */
+#define PWR_STOPENTRY_WFI (0x01U)
+#define PWR_STOPENTRY_WFE (0x02U)
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Regulator_Voltage_Scale PWR Regulator Voltage Scale
+ * @{
+ */
+
+#define PWR_REGULATOR_VOLTAGE_SCALE1 PWR_CR_VOS_0
+#define PWR_REGULATOR_VOLTAGE_SCALE2 PWR_CR_VOS_1
+#define PWR_REGULATOR_VOLTAGE_SCALE3 PWR_CR_VOS
+
+#define IS_PWR_VOLTAGE_SCALING_RANGE(RANGE) (((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE1) || \
+ ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE2) || \
+ ((RANGE) == PWR_REGULATOR_VOLTAGE_SCALE3))
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Flag PWR Flag
+ * @{
+ */
+#define PWR_FLAG_WU PWR_CSR_WUF
+#define PWR_FLAG_SB PWR_CSR_SBF
+#if defined(PWR_PVD_SUPPORT)
+#define PWR_FLAG_PVDO PWR_CSR_PVDO
+#endif
+#define PWR_FLAG_VREFINTRDY PWR_CSR_VREFINTRDYF
+#define PWR_FLAG_VOS PWR_CSR_VOSF
+#define PWR_FLAG_REGLP PWR_CSR_REGLPF
+
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Exported_Macro PWR Exported Macros
+ * @{
+ */
+/** @brief macros configure the main internal regulator output voltage.
+ * When exiting Low Power Run Mode or during dynamic voltage scaling configuration,
+ * the reference manual recommends to poll PWR_FLAG_REGLP bit to wait for the regulator
+ * to reach main mode (resp. to get stabilized) for a transition from 0 to 1.
+ * Only then the clock can be increased.
+ *
+ * @param __REGULATOR__ specifies the regulator output voltage to achieve
+ * a tradeoff between performance and power consumption when the device does
+ * not operate at the maximum frequency (refer to the datasheets for more details).
+ * This parameter can be one of the following values:
+ * @arg PWR_REGULATOR_VOLTAGE_SCALE1: Regulator voltage output Scale 1 mode,
+ * System frequency up to 32 MHz.
+ * @arg PWR_REGULATOR_VOLTAGE_SCALE2: Regulator voltage output Scale 2 mode,
+ * System frequency up to 16 MHz.
+ * @arg PWR_REGULATOR_VOLTAGE_SCALE3: Regulator voltage output Scale 3 mode,
+ * System frequency up to 4.2 MHz
+ * @retval None
+ */
+#define __HAL_PWR_VOLTAGESCALING_CONFIG(__REGULATOR__) (MODIFY_REG(PWR->CR, PWR_CR_VOS, (__REGULATOR__)))
+
+/** @brief Check PWR flag is set or not.
+ * @param __FLAG__ specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+ * was received from the WKUP pin or from the RTC alarm (Alarm B),
+ * RTC Tamper event, RTC TimeStamp event or RTC Wakeup.
+ * An additional wakeup event is detected if the WKUP pin is enabled
+ * (by setting the EWUP bit) when the WKUP pin level is already high.
+ * @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+ * resumed from StandBy mode.
+ * @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
+ * by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode.
+ * For this reason, this bit is equal to 0 after Standby or reset
+ * until the PVDE bit is set. Not available on L0 Value line.
+ * @arg PWR_FLAG_VREFINTRDY: Internal voltage reference (VREFINT) ready flag.
+ * This bit indicates the state of the internal voltage reference, VREFINT.
+ * @arg PWR_FLAG_VOS: Voltage Scaling select flag. A delay is required for
+ * the internal regulator to be ready after the voltage range is changed.
+ * The VOSF bit indicates that the regulator has reached the voltage level
+ * defined with bits VOS of PWR_CR register.
+ * @arg PWR_FLAG_REGLP: Regulator LP flag. When the MCU exits from Low power run
+ * mode, this bit stays at 1 until the regulator is ready in main mode.
+ * A polling on this bit is recommended to wait for the regulator main mode.
+ * This bit is reset by hardware when the regulator is ready.
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Clear the PWR pending flags.
+ * @param __FLAG__ specifies the flag to clear.
+ * This parameter can be one of the following values:
+ * @arg PWR_FLAG_WU: Wake Up flag
+ * @arg PWR_FLAG_SB: StandBy flag
+ */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, (__FLAG__) << 2U)
+
+#if defined(PWR_PVD_SUPPORT)
+/**
+ * @brief Enable interrupt on PVD Exti Line 16.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT() SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Disable interrupt on PVD Exti Line 16.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT() CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Enable event on PVD Exti Line 16.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT() SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Disable event on PVD Exti Line 16.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT() CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief PVD EXTI line configuration: set falling edge trigger.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE() SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Disable the PVD Extended Interrupt Falling Trigger.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE() CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief PVD EXTI line configuration: set rising edge trigger.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE() SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Disable the PVD Extended Interrupt Rising Trigger.
+ * This parameter can be:
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE() CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief PVD EXTI line configuration: set rising & falling edge trigger.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE() do { __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); } while(0);
+
+/**
+ * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+ * This parameter can be:
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE() do { __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); } while(0);
+
+/**
+ * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+ * @retval EXTI PVD Line Status.
+ */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG() (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+ * @brief Clear the PVD EXTI flag.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG() (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+ * @brief Generate a Software interrupt on selected EXTI line.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+/**
+ * @brief Generate a Software interrupt on selected EXTI line.
+ * @retval None.
+ */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT() SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+
+#endif /* PWR_PVD_SUPPORT */
+
+/**
+ * @}
+ */
+
+/** @addtogroup PWR_Private
+ * @{
+ */
+#if defined(PWR_PVD_SUPPORT)
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+ ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+ ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+ ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+ ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+ ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+ ((MODE) == PWR_PVD_MODE_NORMAL))
+#endif /* PWR_PVD_SUPPORT */
+
+#if defined (STM32L010x6) || defined (STM32L071xx) || defined (STM32L072xx) || defined (STM32L073xx) || defined (STM32L081xx) || defined (STM32L082xx) || defined (STM32L083xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+ ((PIN) == PWR_WAKEUP_PIN2) || \
+ ((PIN) == PWR_WAKEUP_PIN3))
+#elif defined (STM32L010xB) || defined (STM32L051xx) || defined (STM32L052xx) || defined (STM32L053xx) || defined (STM32L062xx) || defined (STM32L063xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+ ((PIN) == PWR_WAKEUP_PIN2))
+#elif defined (STM32L010x8) || defined (STM32L031xx) || defined (STM32L041xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+ ((PIN) == PWR_WAKEUP_PIN2))
+#elif defined (STM32L010x4) || defined (STM32L011xx) || defined (STM32L021xx)
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1) || \
+ ((PIN) == PWR_WAKEUP_PIN3))
+#endif
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+ ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
+
+/**
+ * @}
+ */
+
+/* Include PWR HAL Extension module */
+#include "stm32l0xx_hal_pwr_ex.h"
+
+/** @defgroup PWR_Exported_Functions PWR Exported Functions
+ * @{
+ */
+
+/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @{
+ */
+void HAL_PWR_DeInit(void);
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+/**
+ * @}
+ */
+
+/** @defgroup PWR_Exported_Functions_Group2 Low Power modes configuration functions
+ * @{
+ */
+
+#if defined(PWR_PVD_SUPPORT)
+/* PVD control functions ************************************************/
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+#endif
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Define the private group ***********************************/
+/**************************************************************/
+/** @defgroup PWR_Private PWR Private
+ * @{
+ */
+/**
+ * @}
+ */
+/**************************************************************/
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32L0xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+
|